Liquid-Phase Transport During Removal of Organic Binders in Injection-Molded Ceramics

A method has been developed for calculating hydraulic pressures induced by thermal expansion of liquid binders early in the removal cycle, when evaporative losses are negligible and fully saturated conditions prevail. Specific results were obtained for flat compacts containing a common wax binder, mixed with varying amounts of low-density polyethylne. In general, these results show how the risk of hydraulic fracture increases with heating rate and compact thickness. Although pressures are minimal when the binder consists entirely of wax, the continual addition of polyethylene eventually gives rise to unacceptable risk levels, even for relatively thin compacts. Binder removal at elevated temperatures is considered subsequently. In this case, vapor pressures eventually approach a critical level, thereby allowing mass removal by evaporation to overcome the effect of thermal expansion in maintaining full saturation. With the onset of void formation, the developing capillary pressure supersedes hydraulic pressure as the driving force in liquid transport. Besides representing capillary flow, the present formulation also accounts for thermal degradation of the binder during removal. The resulting system of equations was solved numerically for a variety of representative debinding conditions. Predictions for flat compact containing a balanced wax/polyethylene binder indicate that thermal degradation of the polyethylene can give rise to a marked improvement in debinding rates. It turns out, however, that this enhancement is far more effective in thinner compacts.     

Solar barometric distillation for seawater desalting part I: Basic layout and operational/technical features

The report presents an innovative solar barometric distillation technology for seawater desalting (SW-SBD) which has several attractive features such as: (1) efficient vacuum solar collectors of simple construction; (2) a barometric layout for quasi-steady operation at subatmospheric pressure; (3) a demister system of simple mechanical construction; and (4) an electronic control system regulating plant productivity parameters on available solar radiation flux. The proposed seawater desalting technology consists of single-effect distillation with water vapor produced and heated at subatmospheric pressure in a solar collector loop; the basic layout, operational features, and energy efficiency are presented and analysed in detail. Subsequent reports will provide technico-economical data from prototype desalting plants in view of industrial implementation. A promising specific electric energy consumption,∼2 kWm³ offresh water produced, was found by estimating pumping power requirements of major SW-SBD plant pumps. A sizable reduction in produced water cost with respect to an existing solar seawater desalting plant in Abu Dhabi is expected on the basis of a preliminary economic evaluation for a ∼100 m³/d plant prototype.     

Electrochemical anticorrosion performance evaluation of Al2O3 coatings deposited by MOCVD on an industrial brass substrate

Alumina (Al₂O₃) coatings of different thickness were deposited on OT59 brass substrate (BS) using the metal organic chemical vapour deposition (MOCVD) technique to evaluate the corrosion performance by EIS measurements. The used precursor was dimethyl-aluminium-isopropoxide. Electrochemical characterizations of the deposited films were performed in a standard very aggressive acidic solution (aerated 1N H₂SO₄ at 25 °C up to 168 h of immersion time) by means of direct current method (Tafel curves) and electrochemical impedance spectroscopy (EIS). The Rutherford backscattering spectroscopy (RBS) indicated that the films are very pure with the correct Al₂O₃ stoichiometry, while the IR absorption spectra showed that the films did not contain any OH groups. The surface film morphology was investigated by atomic force microscopy (AFM) and displayed a globular texture. The films were very smooth, with a maximum root mean square roughness, for example, of 14 nm for a 0.96 μm thick coating. The EIS data confirmed, as expected, that a 2.40 μm Al₂O₃ layer ensures the best corrosion protection after 168 h of immersion in the very acidic environment used.     

Fluoroelastomers-dependence of relaxation phenomena on composition

The dynamic-mechanical properties of some fluoroelastomers were determined as a function of composition at low frequency (≈ 1 Hz), by means of a free oscillation torsion pendulum, between −180°C and the softening point. Vinylidenefluoride (VDF)-hexafluoropropene (HFP) copolymers of molar composition 0–39% HFP and terpolymers of VDF and HFP with up to 30mol% tetrafluoroethylene (TFE) and a constant VDF to HFP molar ratio of 3.4 were considered. Two relaxation processes typical of the amorphous phase were found. The first, located at about −87°C, is related to local motions and the transition temperature was found to be independent of composition for copolymers, while it depends on TFE molar content for terpolymers. The second is related to the glass transition and the transition temperature depends on the composition. However, for semicrystalline copolymers the double glass transition phenomenon was observed. When crystallinity goes to zero at about 20 mol% HFP, only one transition is observed. It was also found that ordered structures can take place for terpolymers when TFE molar concentration exceeds 20%. The crystal disorder transition of pure PVDF (75°C) is observed also for low HFP concentrations but the transition temperature is strongly reduced. Analogies between the VDF-HFP and E-P systems are also discussed.     

A METHOD FOR GENERATING INDEPENDENT REALIZATIONS OF A MULTIVARIATE NORMAL STATIONARY AND INVERTIBLE ARMA(p, q) PROCESS

Abstract. A method for generating finite independent realizations of a normal multivariate stationary ARMA( p, q ) process is proposed. It is based on an AR (1) representation of an ARMA( p, q ) process allowing for an exact generation of the initial values of the simulation algorithm. Input facilities are supplied in order to assure stationarity and invertibility of the considered process.     

Straightforward modeling of dynamic I–V characteristics for microwave FETs

This work presents a straightforward approach aimed at modeling the dynamic I–V characteristics of microwave active solid‐state devices. The drain‐source current generator represents the most significant source of nonlinearity in a transistor and, therefore, its correct modeling is fundamental to predict accurately the current and voltage waveforms under large‐signal operation. The proposed approach relies on using a small set of low‐frequency time‐domain waveform measurements combined with numerical optimization‐based estimation of the nonlinear model parameters. The procedure is applied to a gallium nitride HEMT and silicon FinFET. The effectiveness of the modeling procedure in terms of prediction accuracy and generalization capability is demonstrated by validation of the extracted models under operating conditions different than the ones used for the parameters estimation. Good agreement between measurements and model simulations is achieved for both technologies and in both low‐ and high‐frequency range. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:109–116, 2014.     

Reactive Compatibilizer Precursors for LDPE/PA6 Blends, 4

Summary: The effectiveness of some thermoplastic elastomers grafted with maleic anhydride (MA) or with glycidyl methacrylate (GMA) as compatibilizer precursors (CPs) for blends of low density polyethylene (LDPE) with polyamide‐6 (PA) has been studied. The CPs were produced by grafting different amounts of MA or GMA onto a styrene‐block‐(ethylene‐co‐1‐butene)‐block‐styrene copolymer (SEBS) (KRATON G 1652), either in the melt or in solution. A commercially available SEBS‐g‐MA copolymer with 1.7 wt.‐% MA (KRATON FG 1901X) was also used. The effect of the MA concentration and of other characteristics of the SEBS‐g‐MA CPs was also studied. The specific interactions between the CPs and the blends components were investigated through characterizations of the binary LDPE/CP and PA/CP blends, in the whole composition range. It was demonstrated that the SEBS‐g‐GMA copolymers display poor compatibilizing effectiveness due to cross‐linking resulting from reactions of the epoxy rings of these CPs with both the amine and the carboxyl end groups of PA. On the contrary, the compatibilizing efficiency of the MA‐grafted elastomers, as revealed by the thermal properties and the morphology of the compatibilized blends, was shown to be excellent. The results of this study confirm that the anhydride functional groups possess considerably higher efficiency, for the reactive compatibilization of LDPE/PA blends, than those of the ethylene‐acrylic acid and ethylene‐glycidyl methacrylate copolymers investigated in previous works.

SEM micrograph of the 75/25 LD08/PA blend (with 2 phr SEBSMA1).